Take the 2-minute tour ×
Geographic Information Systems Stack Exchange is a question and answer site for cartographers, geographers and GIS professionals. It's 100% free, no registration required.

Some common problems with displaying routes created from street data, such as bus routes, include:

  1. Routes may overlap themselves, such as when a route takes the same road in opposite directions
  2. Routes may overlap other routes that take the same street.
  3. Routes are often overly detailed, or "noisy", owing to their derivation from street data.
  4. Indicating a route's direction unambiguously without overloading it with arrows can be a challenge.

What are some techniques for dealing with these issues in order to create a practical and usable route map, such as this Manhattan bus routes map? Do you know of any such public transport maps that were produced by automatic techniques rather than manual illustration/digitization?

Specifically I am using ArcGIS 10, but solutions involving other software are welcome as well.

One technique I have had some success with for dealing with 1) is using ArcMap's cartographic line symbols with a negative offset -- assuming the lines are oriented in the direction of travel, this will offset the lines such that the right and left-hand sides are distinct and oriented as you would expect (at least for right-hand traffic countries, for left-hand traffic countries one would use a positive offset). However the result tends to be a bit wonky around turns, interchanges and and U-turns, and is inflexible when dealing with multiple routes.

Another possibility that I am not very familiar with but which seems promising is cartographic representations -- however, I have not had much luck in finding examples of using representations for transportation maps and whether it might fit the bill.

share|improve this question
1  
Have you considered, or eliminated from consideration, ArcGIS Schematics? esri.com/software/arcgis/extensions/schematics/… –  PolyGeo Jun 20 '12 at 7:41
    
Haven't seen that before so no! (+1) I didn't see any screenshots or mention of it integrating with a map though -- can it be configured to act as a normal layer in a map document, or is it always in a separate non-spatial view? –  blah238 Jun 20 '12 at 9:16

2 Answers 2

up vote 7 down vote accepted

I have not used ArcGIS Schematics for more than some quick demos quite a few years ago, but there is a blog posting on Create route maps with the ArcGIS Schematics extension that may provide a solution.

share|improve this answer
    
That's great, thanks (and almost frighteningly close to what I was looking for!). I am of course interested to see what other options there are while I look into this one so I'll wait for other responses before accepting an answer. –  blah238 Jun 20 '12 at 9:48

I don't think I would recommend this at the start (more as a last resort for simplicity), but I have seen many subway maps actually manipulate the lines to be more orderly. Here is an example from the visual.ly blog depicting U.S. highways. I am pretty sure there are many more floating around though.

Visual.ly highway map

This mainly addresses your point #3, but it helps to partially solve the other problems as well. When the lines are less tortuous it is easier to develop symbology to distinguish between the lines and over-plotting is easier to solve by off-setting symbols.

In terms of time to make they look like alot of work though. Also it is painful to suggest distorting geography to make a nice looking map, but there are some nice examples floating around. I will try to find some more examples and post them back here.

share|improve this answer
    
Great subway style map, can we reach this result using Arcgis Schematics ? –  geogeek Jun 20 '12 at 13:57
    
Thanks for the how to , this is really useful :) –  geogeek Jun 20 '12 at 13:59
1  
@geogeek, I suspect most of the examples were constructed in other vector graphics editing programs. While off-the-cuff the ArcGIS Schematics seems like it will get you part of the way, it doesn't look like it has the ability to manipulate geometries at will like you can in a vector graphic program like Inkscape or Adobe Illustrator. I don't know for sure though, I have never used the tool. –  Andy W Jun 20 '12 at 14:04

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.