Take the 2-minute tour ×
Geographic Information Systems Stack Exchange is a question and answer site for cartographers, geographers and GIS professionals. It's 100% free, no registration required.

I'm really stuck today!! I need my "units" set in CAD to reflect a "compass". I need the bearings I enter to reflect a complete circle with North being 0/360d, East being 90d, South being 180d and west being 270d (as shown in the attachment). I have never had to set my units up this way in CAD. I've always used the survey plan type bearings (ie - N 90d 10' 2" E). I just can't seem to figure out how to set my units properly. I haven't phrased this question very well (sorry), but can anyone help?

enter image description here

share
    
I see that you have precision set to 0. You should use at least mins " for the call in your question. to set what you are asking about you select the direction button below. and set the north angle. –  Brad Nesom Apr 25 '11 at 18:22
    
Hey Brad -- The print screen is actually arbitrary. It is not a reflection of the settings I have chosen. I just opened a default CAD drawing to use for the image I attached. I think I'm getting close here. Suggestions still welcome however!! –  Dano Apr 25 '11 at 18:29
    
Try setting ANGBASE system variable to 90 and ANGDIR to 1, maybe that will help. –  Mario Miler Apr 25 '11 at 18:41

2 Answers 2

up vote 2 down vote accepted

That (screenshot) is where you need to make the changes. you use degrees for angle and set yoru precision to second or decimal seconds dependong on your calls. 90d45'36.05".
Select whether you want clockwise or counter with the checkbox in your screenshot.
Then in the direction you set the north direction.

As described here on dotsoft.com...

How do I enter boundaries in bearing & distance?

First you need to set the appropriate units in the DDUNITS command. Set the angular units to 'Surveyor', then choose the direction button and make sure that 'Angle Direction' = east, 'Rotation' = counter clockwise. Even though you have set to Surveyors Units it won't work right unless set this way.

Then using the LINE or PLINE command you enter the calls as relative polar coordinates.

Command: LINE
Start Point: (Pick One)
Next Point: @123.45 < N45D30'15"E
Next Point: @234.56 < S25D10'10"W

Notice the syntax for the relative polar coordinate. You put the @ sign first, which means relative to the last point. Next comes the distance. Last is the bearing. Its enclosed in the quadrant NE, NW, SE, SW, note the use of letter D to indicate the degrees.

share
    
There seems to be some corruption of the text: perhaps `90d45'36.05"' belongs in the command example? –  whuber Apr 25 '11 at 20:40
    
I gave you a check Brad. Most of this answer is actually "exactly" what I've done. I did adjust the precision, and as you said, I set the direction to North (and toggled "clockwise"). The settings seem to have worked. If I wanted to go due west at 50 metres, I just typed @50<270 and it worked. I couldn't get CAD to treat the circle as a 360 degree animal!! It wanted to break it in to halves (east & west). I'm just drafting in a fresh drawing, and I'll copy/paste everything over once it's all in place. –  Dano Apr 25 '11 at 20:46
    
@whuber - that just refers to the angle at which I want the line drawn. In Brads example, my line would be drawn at an angle of 90 degrees, 45 minutes and 36.05 seconds relative to the starting point of the polyline. What starts to get crazy in CAD, is getting that directionality set properly!!! Well .... for me anyway!!! –  Dano Apr 25 '11 at 20:57
    
@Dano But the command example does not follow the syntax @Brad described and the "90d....05" text is completely out of place. It looks like part of the answer got translocated to an unintended location or maybe even worse stuff happened (which is why I'm asking about this in a comment rather than attempting an edit). –  whuber Apr 25 '11 at 21:02
    
I see what you mean now. It almost looks like an accidental copy/paste to me ... as though he was editing and accidentally pasted it there without realizing. Yes .... it looks as though it should follow the "@123.45". There should be a "<" in the middle too. I understand what you meant now ... sorry. :o) –  Dano Apr 25 '11 at 21:09

try

Menu>Format>Units

command line: units

http://docs.autodesk.com/ACD/2010/ENU/AutoCAD%202010%20User%20Documentation/index.html? url=WS1a9193826455f5ffa23ce210c4a30acaf-527c.htm,topicNumber=d0e328054

Base Angle Sets the direction of the zero angle. The following options affect the entry of angles, the display format, and the entry of polar, cylindrical, and spherical coordinates.

East Specifies the compass direction east (the default).

North Specifies the compass direction north.

West Specifies the compass direction west.

South Specifies the compass direction south.

Other Specifies a direction different from the points of the compass.

Angle Specifies a value for the zero angle when Other is selected. You can specify the angle by entering a value.

Pick an Angle Button Defines the zero angle in the graphics area based on the angle of an imaginary line that connects any two points you specify with the pointing device. Available only when Other is selected.

share

This site is currently not accepting new answers.

Not the answer you're looking for? Browse other questions tagged .