5
votes
2answers
470 views

How to extract coordinates & elevations of boundary cells of a DEM

I am using a 50mx50m grid irregular shaped DEM file.I have to work on the boundary conditions. How do i extract the cell locations ( in x,y coordinate ) along the boundary edge and consequently find ...
2
votes
1answer
617 views

How to know if flow accumulation map reflects true catchment areas?

I have calculated flow accumulation (img file) using this DEM (img file), which is 0.5 degree resolution, using arcmap. I am wondering if the cell accumulation value can directly be translated into ...
1
vote
0answers
26 views

Can I burn stream network into DEM using DEM layer only? [duplicate]

Possible Duplicate: How to ‘burn’ a stream network into a DEM layer in ArcGIS 10? I am doing hydrology modelling and I want to calculate the run-off. In order to do that,the model which I ...
4
votes
1answer
215 views

DEM local adjustments - terraforming

I'm looking for software that can perform local adjustments in DEMs with tools similar to paintbrushes used in graphics editing programs but streamlined to respect geomorphology. To give you an idea ...
3
votes
1answer
922 views

DEM: How to convert a mosaic dataset to TIN?

I merged several DEMs together in on single DEM with mosaic dataset. Now I wanted to convert this mosaic dataset in Vector with TIN. But when I use the tool (3D Analyst Tool) Raster to TIN comes an ...
3
votes
2answers
229 views

how to fill voids in ASTER stereo-images for DEM generation?

I'm trying to use a stereo-pair of ASTER images to generate a DEM (in ERDAS Imagine). However, the mountains are rather cloudy and the images can't be used as they are. But the relevant parts (valley ...
5
votes
2answers
2k views

Viewsheds and Observer Points in ArcGIS Spatial analyst

I am trying to understand the viewshed and observer points tool in spatial analyst. I want to show which areas of land can see a wind turbine, or put another way, from where can the wind turbine be ...
5
votes
2answers
4k views

Correct way to create a DEM from point data in csv files

I know this might seem a somewhat general question, but I have to start somewhere. I have a lot of csv files which contain point data containing height, aspect and slope measurements at a resolution ...
3
votes
2answers
4k views

Replacing Raster Values in Ras1 with Ras2

I have two rasters Ras1 and Ras2. I want to change the Ras1. In Ras1, there are few areas, lines, points I am interested having nodata cells and wrong data cells.(limited to interested areas only ...
2
votes
2answers
127 views

Finding Two locations with a conditional search on DEM

I want to find two locations H difference in elevation between two locations on a DEM. Ex: point A and B are my output after search on DEM. conditions are (1)buffer R distance around point A and (2) ...
6
votes
1answer
336 views

Problems creating TIN from British Columbia DEM data

Is anyone familiar with creating a TIN using ArcGIS9.3 and British Columbia DEM data (.GEN files)? I can't figure out how to get the breaklines to work during the creation of the TIN. Using ...
6
votes
3answers
1k views

How to find the elevation differences between adjacent pixels in ArcGIS?

Is there a way to determine what the difference in elevation is between two adjacent pixels? I am using an SRTM DEM to map faults. I am using the vertical error (>16m) as a criterion for the ...
4
votes
1answer
545 views

Is it possible to reverse the trend/values of a raster?

For example - if I have a raster DEM covering a stream with higher elevations in the west (up river) and lower elevations in the east (down river) is it possible to reverse this trend so that the east ...
5
votes
1answer
324 views

When merging two DEMs, do they have to be in the same pixel bits?

I have a simple question. I have 2 different Digital Elevation Modeling (DEM). One is the state DEM and has 30m and has 16 pixel bit. I have a couple of smaller DEM that has 30m but they have 32 pixel ...
1
vote
2answers
1k views

DEM problem in ArcGIS

I have a 32 bit DEM with resolution 0.5 * 0.5 and range of elevation is 1299 to 1489. When I want to export or use copy raster tool or create fill in Arcgis, the results are elevation between ...
1
vote
1answer
435 views

Importing ERDAS-processed GTOP030 dem data into ARCGIS

I have two GTOP030 DEM images. After downloading them, I have imported into ERDAS and mosaiced them. Then I have exported it to .tif file in order to open it in ARCGIS. But when I tried to open it in ...
3
votes
1answer
652 views

Solar radiation calculation from GTOP030 DEM image

Can you help me to calculate solar radiation from GTOPO30 DEM image at the 30 m spatial resolution. I'm trying to do this many times using spatial analysis-solar radiation calculation tool in arcgis. ...
4
votes
1answer
937 views

How do I know if the DEM has z values?

How do I know if the DEM contains z-values ? By looking at the DEM's layer properties and it does not mention the z values. I then add it to the ArcScene and tried to find it..nothing... It only ...
2
votes
1answer
641 views

Combine DEM raster with vector data. in ArcScene 9.3

Ive have a raster layer of earthquake data that includes depth. I also have a DEM file. The problem is that I need to plot earthquake depth relative to the DEM file rather than sealevel in order to ...
4
votes
2answers
610 views

comparing two TINs

i have the following two files: 1) LiDAR las file1 2) Let's give it a name LiDAR las file2, contains the same file1 data, where number of points randomly removed. So if file1 contains X number of ...
6
votes
1answer
606 views

Interpolation: irregular shape, merging DEM's

my problem is quite complex, though I hope that solution may be simple or at least possible. I do have .img DEM 0.5x0.5m. DEM consists of river bed, river valley and adjacent areas (it is strip of ...
1
vote
3answers
2k views

Where can I download 1 arc-second elevation data for Canada other than Geobase?

Can someone suggest a source for Canadian elevation data better or equivalent to 1 arc-second? I have a good data source for Ontario but for other provinces folks often recommend Geobase which claims ...
4
votes
5answers
3k views

Problems merging DEMs or other raster datasets? Clipping Raster dataset to vector line?

I have two DEMs that I am going create a hillshade from, and ultimately want one hillshade clipped to a county boundary. I am running into a couple problems, though. When I try to merge the two ...